Click to enlarge

chevron_left
navigate_next

Glove Juba - 311BGC1 FIRE-FIGHTER

Name: 311BGC1
Brand: Juba

Water-repellent cow grain leather glove reinforced on palm, thumb, between thumb and index finger.

Normative

3234B

EN388:2016 Protective gloves against mechanical risks.
The EN388: 2003 standard is renamed EN388: 2016, the year of its revision. The reason for the modification is given by the discrepancies in the results between laboratories in the knife cut test, COUP TEST. Materials with high levels of cut produce a dulling effect on the circular blades, which undermines the result.

The new regulation was published in November 2016 and the previous one is from the year 2003. During these 13 years, there has been a great innovation in the materials for the manufacture of cutting gloves, they have forced to introduce changes in the tests to be able to measure with more rigorous levels of protection.

pictograma 388 pictograma 388A1

A - Abrasion resistance (X, 0, 1, 2, 3, 4)
B - Blade Cut Resistance (X, 0, 1, 2, 3, 4, 5)
C - Tear resistance (X, 0, 1, 2, 3, 4)
D - Puncture resistance (X, 0, 1, 2, 3, 4)
E - Cutting by sharp objects ISO 13997 (A, B, C, D, E, F)
F - Impact test complies / does not comply (It is optional. If it complies, put P)

EN388:2016 PERFORMANCE LEVELS	1	2	3	4	5
6.1 Abrasion resistance (Cycles)	100	500	2000	8000	-
6.2 Blade cut resistance (Index)	1,2	2,5	5	10	20
6.4 Tear resistance (Newtons)	10	25	50	75	-
6.5 Puncture resistance (Newtons)	20	60	100	150	-

ENISO13997:1999 PERFORMANCE LEVELS	A	B	C	D	E	F
6.3 TDM: Cut resistance (Newtons)	2	5	10	15	22	30

Minimum levels are required for standards EN388 and EN407 and minimum lengths.

MINIMUM LENGTH
SIZE	MINIMUM LENGTH
6	260 mm
7	270 mm
8	280 mm
9	290 mm
10	305 mm
11	315 mm

MINIMUM REQUIREMENTS
Abrasion resistance	Minimum 2000 cycles (Level 3)	Complies
Cut resistance	Minimum 2.5 (Level 2)	Complies
Tear resistance	Minimum 50 N (Level 3)	Complies
Puncture resistance	Minimum 100 N (Level 3)	Complies
Flame resistance	t Post-combustion ≤ 2s t Post-glow ≤ 5s (Level 4) The material does not leak The seams do not open	Complies
Convective heat resistance	HTI₂₄ ≥ 13 s (Level 3)	Complies
Radiant heat resistance	Heat irradiation time > 22 s	Complies
Contact heat resistance	At 250º C ≥ 10 s	Complies
Lining material heat resistance	At minimum 180ºC: Does not melt - Does not drip or burn	Complies
Shrinkage due to heat	At 180ºC < 5%	Complies
Dexterity	Minimum Level 1 (11 mm rod)	Complies
Resistance to breakage of seams	>- 350 N	Complies
Glove removal time	< 3 s	Complies
Water penetration resistance (optional)	Levels 1 to 4 depending on the time it takes for the water to pass through the glove	Complies
Chemical penetration resistance - (H2SO4) = 30% Sulfuric acid - (NaOH) = 40% Sodium hydroxide - (HCl) = 36% Hydrochloric acid - Heptane	Does not penetrate Does not penetrate Does not penetrate Does not penetrate	Complies

4242XX

Ratified by the Spanish Standardisation Association in June 2020.

Main changes:

Extension of the scope of the standard to domestic use: oven mitts/gloves.
Gloves that reach a level 3 or 4 of any thermal property must reach at least a level 3 in flame propagation. Otherwise, the maximum level that may be reached in the relevant thermal property shall be level 2.
Propagation limited to flame: prohibition of hole formation. Reduction of maximum post-combustion time for level 1. Change in ignition timing.
Heat by contact. Obligation to test any material coming in contact with heat.
Tear resistance. This trial is included.
Convective heat. The test is performed without reinforcement.
New pictogram, for gloves without flame protection.
A minimum length is introduced when resistance against small molten metal splashes is present.
After heat resistance tests, the samples must not suffer signs of melting or holes.

MINIMUM LENGTH OF THE TESTED GLOVES FOR E OR F
SIZE	LENGTH
5	290
6	300
7	310
8	320
9	330
10	340
11	350
12	360
13	370

A - Flame Behaviour
Changes in method and table. To perform the test, the ignition time now goes from 15 to 10" and the post-ignition time for level 1 goes from 20 to 15".

LEVEL OF PREFORMANCE	POST-INFLAMMATION TIME	POST IGNITION TIME
1	≤ 15	Not required
2	≤ 10	≤ 120
3	≤ 3	≤ 25
4	≤ 2	≤ 5

B - Heat by contact
Changes in the test method. In EN407:2004 only the palm is tested, whereas with EN407:2020 any other point that may come into contact is tested.

Contact temperature
Threshold time (S)

LEVEL OF PERFORMANCE	CONTACT TEMPERATURE	THRESHOLD TIME (S
1	100	≥ 15
2	250	≥ 15
3	350	≥ 15
4	500	≥ 15

C - Convective heat
Changes in the test method. From EN373 to ENISO9185:2007

LEVEL OF PERFORMANCE	HTI HEAT TRANSFER RATE
1	≥ 4
2	≥ 7
3	≥ 10
4	≥ 18

D - Radiant heat
There are no modifications. Internal layers must not show signs of melting or show holes.

LEVEL OF PERFORMANCE	HEAT TRANSFER RATE T₃
1	≥ 7
2	≥ 20
3	≥ 50
4	≥ 95

E - Small splashes
There are no modifications. Internal and external layers may not be melted or pierced.

LEVEL OF PERFORMANCE	NUMBER OF DROPS
1	≥ 5
2	≥ 15
3	≥ 25
4	≥ 35

F - Large splashes
Changes in the test method.

LEVEL OF PERFORMANCE	CAST IRON (G)
1	30
2	60
3	120
4	300

Materials

Leather

Colour

Black / Yellow

Length

S - 27 cm

M - 28 cm

L - 29 cm

XL - 29,5 cm

XXL - 31,5 cm

XXXL - 32,5 cm

XXXXL - 33,5 cm

Sizes

7/S

8/M

9/L

10/XL

11/XXL

12/3XL

13/4XL

Packaging

5 pairs/package

50 pairs/box

Characteristics

Extra quality leather
HDry inner membrane that provides total impermeability
Better insulation without losing breathability
Protection against dust particles, chemical substances and greater thermal resistance
Pre-curved pattern to increase user comfort
Reinforcement between thumb and forefinger, area of greatest wear
100% para-aramid fiber (Kevlar®) elastic lining and cuff with vein covers for added protection
Entirely sewn with 100% Kevlar® thread
Carabiner to hang the gloves
Resistance to contact heat (250ºC for 15 seconds), excellent behavior to flame and convective heat.
Complies with EN659: 2003 + A1: 2008 + AC: 2009 Protective gloves for firefighters
Neutral individual bag.

Working gloves suitable for:

Firefighters
Release works
Forestry

Documentation

article Data sheet article Declaration of comformity

Consult a Technician

We can advise you which is the most suitable glove for your job

Consult a Technician

Glove Juba - 311BGC1 FIRE-FIGHTER

Normative

Materials

Colour

Length

Sizes

Packaging

Characteristics

Working gloves suitable for:

Documentation

Consult a Technician

Juba SSP

Technical Consultation